Piston Air Compressor SC-100 LB30A (220 V, 100 L, 420 l/min, 10 bar)

The SC-100 LB30A professional belt-driven oil-lubricated piston air compressor is designed to generate and supply compressed air at working pressures up to 10 bar (1.0 MPa) for pneumatic machinery, air tools, and automated production systems. This unit is engineered as a 100% functional, dimensional, and structural analog of the widely recognized European/Belarusian Remeza (AirCast) СБ4/С-100.LB30A compressor.

The machine is powered by the battle-tested, heavy-duty cast iron LB30A pump unit — a two-cylinder, single-stage configuration with in-line cylinders. A rugged V-belt transmission reduces the electric motor’s nominal speed of 2850 rpm down to an optimal 1150 rpm at the crankshaft. This low-speed design dramatically minimizes mechanical friction, internal working temperatures, and cyclic thermal stresses on the valve assembly, providing exceptional durability and simple field serviceability.

6 People watching this product now!
Description

1. Purpose and Operating Principle

The key feature of the «A» modification is its single-phase power supply — 220 V (50 Hz) with a 2.2 kW (3.0 HP) motor. This enables high-output commercial performance (420 l/min inlet displacement) in facilities where 380 V 3-phase power is unavailable: automotive workshops, tire service centers, paint booths, metal fabrication shops, and construction sites. The horizontal 100-liter air receiver dampens pressure fluctuations, provides an abundant air reserve for high-consumption tools, and facilitates natural air cooling and moisture condensation.


2. Technical Specifications

Parameter Specification
Compressor Model SC-100 LB30A
Reference / Cross-Model Remeza СБ4/С-100.LB30A (AirCast Series)
Compressor Type Reciprocating piston, oil-lubricated, belt-driven
Pump Unit Type Two-cylinder, single-stage, heavy-duty cast-iron block (LB30A type)
Cylinders / Compression Stages 2 / 1
Cylinder Bore 65 mm
Air Receiver Tank Volume 100 L (horizontal, wheel-mounted with anti-vibration feet)
Inlet Air Displacement (Suction) 420 l/min
Free Air Delivery (FAD / Output) ~340 l/min
Maximum Working Pressure 10 bar (1.0 MPa / 145 psi)
Cut-In Pressure (Pressure Switch Delta) 8 bar (0.8 MPa)
Rated Motor Power 2.2 kW (3.0 HP)
Power Supply Voltage / Frequency 220–230 V / 50 Hz (Single-Phase AC)
Pump Crankshaft Speed ~1150 rpm
Pressure Control Assembly CONDOR (Germany) pressure switch with unloader valve
Valve Reed Material Swedish SANDVIK 7C27Mo2 hardened valve spring steel
Cylinder Head Gasket USA-made INTERFACE high-temperature non-asbestos composite
Piston Rings CYPR high-precision wear-resistant rings
Crankshaft Bearings C&U (precision radial bearings from C&U OEM facility)
Drive Belts SANLUX heavy-duty reinforced V-belts
Pump & Tank Finish Eco-friendly water-based anti-corrosion paint
Outlet Air Connection G 1/2″ (BSPP) ball valve + Rapid universal quick coupler (Euro type)
Guaranteed Air Tank Lifespan 7–10 years (with regular daily condensate drainage)
Net Weight ~88 kg
Overall Dimensions (L×W×H) 1150 × 490 × 850 mm

⚠️ Unconfirmed Parameters:

  • Electrical connection details: factory-supplied with a standard 16 A single-phase plug. When operating beyond 10 m from the electrical panel, a dedicated copper wiring cross-section of at least 3×2.5 mm² and a C16–C20 A circuit breaker are recommended to avoid startup voltage drop.
  • Initial factory oil grade: delivered with break-in oil. A complete oil change is recommended after the first 50 operating hours with dedicated ISO VG 100 / DIN 51506 VDL 100 piston compressor oil (e.g., Shell Corena S2 P 100 or Mobil Rarus 427; KS-19 oils are not recommended).

3. Design and Engineering Features

Model Code Breakdown (SC-100 LB30A):

Code Segment Designation Engineering Description
SC Piston Air Compressor Industrial professional reciprocating compressor series
100 Receiver Tank Size 100-liter welded steel pressure vessel
LB30 Pump Type Two-cylinder cast-iron pump block (⌀65 mm pistons, 50 mm stroke)
A Single-Phase Version 2.2 kW electric motor adapted for standard 220 V single-phase grids

Premium Tier Components:

  1. USA-Made INTERFACE Cylinder Head Gasket: The cylinder head gasket is the single most thermally and mechanically stressed sealing component on an air compressor pump (subject to temperatures up to +180 °C and cyclic 10-bar pressure shocks). The SC-100 LB30A utilizes authentic INTERFACE (USA) high-temperature non-asbestos composite material. It completely eliminates cross-cylinder blow-by and micro-leaks, ensuring stable volumetric efficiency over years of continuous operation.
  2. CYPR Precision Piston Rings: Piston assemblies are fitted with rings manufactured by CYPR — a globally recognized OEM engine and compressor ring manufacturer. Precision ring gap geometry and specialized surface heat treatment deliver instant bedding against the cast-iron cylinder walls during the break-in stage, minimizing oil carryover and dry friction.
  3. C&U Precision Crankshaft Bearings: The crankshaft is supported by heavy-duty radial ball bearings manufactured on the OEM lines of the C&U facility — an industry-leading tier-1 bearing supplier for automotive and heavy industrial machinery. These bearings withstand high continuous radial tension from the drive belts while reducing running vibration.
  4. SANDVIK 7C27Mo2 (Sweden) Valve Reeds: The heart of the pump is its valve reed cluster made of authentic Swedish SANDVIK 7C27Mo2 flapper valve steel. The alloy provides unmatched fatigue resistance under millions of cyclic opening/closing cycles (up to 19 strokes per second) while retaining elasticity under high discharge temperatures, preventing valve edge chipping or flapper failure.
  5. SANLUX Reinforced V-Belts: High torque transfer is achieved with industrial-grade SANLUX V-belts. Low-stretch polyester cord reinforcement ensures positive grip and prevents pulley slip during heavy cold starts under load.
  6. Genuine German CONDOR Pressure Switch: Automated start/stop control is governed by an authentic German CONDOR MDR pressure switch. The heavy-duty contact block handles high inrush currents of the 2.2 kW single-phase motor without contact welding or pitting. An integrated unloader valve vents discharge manifold pressure upon shutdown for effortless motor restarts.
  7. Environmentally Friendly Water-Based Paint: The cast-iron pump and crankcase are finished with eco-friendly water-based industrial paint. It provides heat and oil resistance without releasing volatile organic compounds (VOCs).

Manufacturing Quality Control (QC) Standards:

  • 100% CNC Machined Crankcases: Every single crankcase is machined on multi-axis CNC centers, guaranteeing true bearing alignment and cylinder mating parallelism.
  • 2-Hour CMM Metrology Inspection: Crankcase geometry is randomly sampled every two hours using a Three-Coordinate Measuring Machine (CMM) to confirm micron-level tolerances.
  • Dedicated Assembly Line: Compressor pumps are assembled on a specialized production line utilizing calibrated torque tools.
  • 100% Individual Leakage Testing: Every pump undergoes pneumatic pressure leakage testing prior to packaging and dispatch.
  • 3-Minute Pump Run-In Test: Each bare pump unit runs on a testing bench for at least 3 minutes.
  • 5-Minute Complete Compressor Bench Test: Every fully assembled compressor unit (with motor, tank, and controls) is bench-tested under full working pressure for at least 5 minutes.
  • Durable Air Receiver Tank: The certified steel receiver features a guaranteed service life of 7–10 years when drained regularly.

4. Installation and Commissioning Guidelines

  • Electrical Connection (220 V): The single-phase 2.2 kW motor pulls peak startup currents of 25–30 A.

    ❗ Important: Connect exclusively to a dedicated branch circuit using copper cabling with a cross-section of at least 2.5 mm² protected by a C16–C20 A breaker. Never operate the compressor via thin extension leads or coiled cable drums: severe voltage drops below 200 V cause capacitor overheating and trigger motor thermal cutouts.

  • Oil Level Inspection: The compressor is shipped filled with oil. Prior to startup, place the machine on a flat horizontal floor and ensure the oil level aligns dead-center with the red dot on the crankcase sight glass.
    • Use only dedicated reciprocating compressor oils: ISO VG 100 / DIN 51506 VDL 100 (e.g., Shell Corena S2 P 100, Mobil Rarus 427).
    • ⛔ Never use automotive engine oil or KS-19 oil: detergent additives in motor oils break down under discharge heat and bake into heavy carbon deposits on the Sandvik valve reeds, while inferior oils accelerate CYPR ring wear!
  • Break-In Routine: For the first 50 operating hours, operate the machine under moderate duty cycles (duty factor not exceeding 60%). At 50 hours, perform a complete oil drain and refill, then check and cross-torque the cylinder head bolts on a cold pump. Subsequent oil changes should occur every 300–500 operating hours or annually.
  • Daily Condensate Drainage (7–10 Year Tank Life): Air compression naturally generates water condensation inside the tank. Open the bottom drain cock at the end of every working day at 1–2 bar residual pressure to purge moisture and oily residue completely. Keeping the tank drained prevents internal corrosion.
  • Pneumatic Piping Connection:
    • The discharge outlet is equipped with a G 1/2″ (BSPP) parallel male thread ball valve. Seal connections exclusively with a flat sealing ring or gasket. Do not wrap excessive PTFE tape around parallel threads.
    • When plumbing into permanent workshop distribution piping, install a flexible vibration-absorbing hose (minimum 500 mm length) directly at the compressor discharge.
  • Ventilation Clearance: Maintain at least 50 cm of free space from adjacent walls so the pulley fan can draw unobstructed cooling airflow across the finned cylinders.

5. Equivalents and Comparison

Comparison Table:

Parameter / Subsystem SC-100 LB30A Remeza СБ4/С-100.LB30A Remeza СБ4/С-50.LB30A Remeza СБ4/С-100.LB30 (380V)
Pump Unit Cast Iron LB30A (2-Cyl. / 1-Stg.) Cast Iron LB30A (2-Cyl. / 1-Stg.) Cast Iron LB30A (2-Cyl. / 1-Stg.) Cast Iron LB30 (2-Cyl. / 1-Stg.)
Receiver Volume 100 L 100 L 50 L (compact) 100 L
Supply Voltage 220 V (Single-Phase) 220 V (Single-Phase) 220 V (Single-Phase) 380 V (3-Phase)
Motor Power 2.2 kW 2.2 kW 2.2 kW 2.2 kW
Inlet / Outlet Air Flow 420 / ~340 l/min 420 / ~340 l/min 420 / ~340 l/min 420 / ~340 l/min
Max Pressure 10 bar 10 bar 10 bar 10 bar
Cylinder Head Gasket INTERFACE (USA) Reinforced composite Reinforced composite Reinforced composite
Valve Plates SANDVIK 7C27Mo2 (Sweden) Standard spring steel Standard spring steel Standard spring steel
Pressure Switch CONDOR (Germany) CONDOR / Equivalent CONDOR / Equivalent CONDOR MDR 3
Parts Compatibility 100% Identical Reference standard Reference standard Partial (380V electricals)

Key Advantages of SC-100 LB30A:

  • 100% Interchangeable Parts: Air intake filters, valve plates, connecting rods, pistons, rings, gaskets, and drive pulleys match Remeza LB30A spare parts lists completely. Replacement parts are stocked locally in Chisinau by Acvatron SRL.
  • Top-Tier Global Components: Combining Swedish Sandvik steel, American Interface gaskets, and German Condor controls provides superior endurance in severe industrial environments.

6. Common Operating Mistakes

  1. Using Light-Gauge Extension Cords: Powering through thin wires (0.75–1.5 mm²) causes line voltage to dip to 175–185 V during motor startup. The motor stalls under pressure, start capacitors overheat, and the thermal protection button trips.
  2. Ignoring Condensate Draining: Neglecting moisture drainage can accumulate 15–20 liters of stagnant water inside the receiver over months. This degrades effective tank capacity, increases motor cycling, and causes rust carryover into air lines.
  3. Using Automotive Motor Oil: Automotive engine oils contain detergents that bake into heavy carbon deposits on Sandvik valve plates under high compressor heat. Valves lose their seal, the head overheats past +200 °C, and air output collapses.
  4. Operating in Dusty Environments Without Filter Maintenance: In body shops or woodworking areas, airborne particulate clogs paper intake filters rapidly, dropping air displacement and acting as an abrasive on CYPR rings.
  5. Pulley Misalignment After Belt Adjustment: Re-tensioning belts without verifying parallel pulley alignment leads to rapid SANLUX belt edge wear and uneven diagonal loading on the crankshaft bearings.

7. Applications

The SC-100 LB30A compressor serves as a dependable compressed air source across commercial and industrial operations:

  • Automotive and Tire Service Facilities: Operating 1/2″ pneumatic impact wrenches (150–250 l/min demand), air ratchets, die grinders, air jacks, fluid evacuators, and tire inflation lines.
  • Automotive Spray Booths & Finishing: Powering professional HVLP and LVLP paint guns (200–280 l/min air demand) in conjunction with air preparation moisture filters.
  • Furniture and Woodworking Shops: Driving pneumatic framing nailers, staple guns, and blow guns for clearing sawdust.
  • Plasma Arc Cutting: Providing stable 5–6 bar air delivery for plasma cutting power supplies (e.g., CUT 40 / CUT 60).
  • Construction & Interior Finishing: Supplying air for hopper guns, plaster sprayers, and caulking guns.

8. Expert Opinion

«In the 220V compressor category, the heavy-duty cast-iron LB30A pump has long stood as an industry benchmark for durability in Moldova. The greatest strength of the SC-100 LB30A is its 100% serviceability paired with premium wear components.

Look closely at the hardware: it comes equipped with Swedish Sandvik 7C27Mo2 valve reeds, USA-made Interface head gaskets, and authentic German Condor switchgear. Precision CNC crankcase machining combined with 2-hour CMM dimensional checks provides perfect alignment for the C&U bearings, eliminating vibration.

Because this compressor shares dimensions and parts with the Remeza СБ4/С-100.LB30A, spare parts are readily available off-the-shelf in Chisinau. My engineering advice: provide a clean 220V power supply via 2.5 mm² copper cable, run only quality ISO VG 100 compressor oil (Shell or Mobil, never cheap oils), and drain water daily — under this care, this unit will easily deliver 10 years of reliable service.»

— Vitali Boluchevski, Lead Engineer, Acvatron SRL, 18 years of experience


9. Frequently Asked Questions (FAQ)

1. Is the SC-100 LB30A a direct replacement for the Remeza СБ4/С-100.LB30A?

Yes, it is a 100% functional, geometric, and dimensional equivalent. It shares the identical 420 l/min displacement, 100-liter receiver, and two-cylinder LB30A cast-iron pump. All maintenance parts (valves, rings, gaskets, filters, belts) are fully interchangeable.

2. Can the compressor run on a standard domestic 220 V circuit?

Yes, it is purpose-built for single-phase 220–230 V power grids. The 2.2 kW motor is equipped with both start and run capacitors, and the CONDOR pressure switch features a mechanical unloader valve for smooth startups. A dedicated copper circuit with 2.5 mm² wiring and a C16–C20 A breaker is required.

3. Which compressor oil is required, and how often should it be changed?

Use dedicated reciprocating compressor oils meeting ISO VG 100 / DIN 51506 VDL 100 standards (such as Shell Corena S2 P 100 or Mobil Rarus 427). Automotive oils and substandard oils like KS-19 must not be used due to valve coking risks. The first change is due at 50 break-in hours, followed by changes every 300–500 hours or annually.

4. What is the expected service life of the 100-liter air tank?

The heavy-duty steel receiver features a guaranteed operational life of 7–10 years. The key maintenance condition is regular (daily) drainage of accumulated condensation through the bottom drain valve. Without standing moisture, internal oxidation is prevented.

5. What quality control inspections does each unit undergo?

Each compressor is subjected to stringent factory QC: 100% of crankcases undergo CMM coordinate measurement, every pump unit is pneumatically tested for leaks, and every pump runs on a test bench for at least 3 minutes. The completed compressor is bench-tested under full 10-bar pressure for at least 5 minutes. In addition, Acvatron SRL performs pre-delivery verification prior to customer handover.

0 reviews
0
0
0
0
0

There are no reviews yet.

Be the first to review “Piston Air Compressor SC-100 LB30A (220 V, 100 L, 420 l/min, 10 bar)”

Your email address will not be published. Required fields are marked *

You have to be logged in to be able to add photos to your review.